At a Glance
Your LG dehumidifier removes excess moisture in your home caused by humid conditions, giving you more dry and comfortable air
- The product operates at temperatures from 41℉ to 90℉.
- Using the product outside this temperature range may freeze the inside of the unit or cause the product to overheat.
- The product may increase room temperature by about 5℉.
LG Dehumidifier - General Usage
Your LG dehumidifier removes excess moisture in your home caused by humid conditions, giving you more dry and comfortable air.
Before you start using the product, keep in mind that the product operates at temperatures from 41℉ degrees to 90℉ degrees.
Avoid using the product outside this temperature range for water may freeze inside the product where the product may overheat.
Also the product may increase room temperature by about 5℉ degrees.
If you turn on the product and immediately restart it, it will take up to 3 minutes before the product begins to dehumidify. This is normal unnecessary to put like the product.
To start the humidifying, press Power to turn on the product.
The display will show the current humidity level between the range of 25 to 90 percent.
Press the Up and Down buttons to gesture desired humidity setting in the range of 30 to 80 percent.
The display shows the desired humidity level and after 5 seconds reverts to the current humidity level.
Make sure to set the desired humidity level below the current humidity level.
Press the Fan Speed button to select either High or Low speed.
Using the timer function allows you to set the product to automatically shut off after a fixed amount of time.
You can set it to 1 to 12 hours.
The product will turn off once a timer expires, or if the water bucket is full.
In order to avoid the water bucket filling up before the timer ends, it's recommended to empty the water bucket before setting the timer.
To disable the timer repeatedly press the timer button until 12 appears and press once more.
The Safety Standby light turns on after 23 hours of continuous operation.
For 1 hour the product will temporarily shut off to prevent product malfunction and will automatically resume operation.
The bucket full light turns on when the water bucket is full, remove the water bucket empty the water and replace the water bucket.
The Check Filter light turns on after 350 hours for 15 days of continuous operation. Check the filter and clean it if necessary.
After cleaning filter, press and hold the Filter Reset button for 3 seconds to reset the operating time back to 0 hours.
The Auto Defrost function turns on automatically to remove any frost in the product caused by cold temperatures.
During this function the compressor will stop. Wait for the Auto Defrost cycle to end and auto defrost light will turn off and the product will resume.
Before you enter the water bucket, turn off the product and unplug it.
Pull the top handle of the water bucket to remove it from the product.
If you notice that water is dripping, remove it with a soft cloth.
Remove the cover and pour out the water.
Put the cover back on replace the water bucket into the product.
Make sure to angle the bottom and then push the top into place.
Try This
-
Power On the Unit
Press
to turn on.
-
Set the Humidity Level
Press the
and
buttons to change humidity.
- The desired humidity level can be set in 5% increments from 30-80%.
- The display shows the desired humidity level while it is being set, then reverts to the current humidity level after 5 seconds.
- The current humidity level is displayed in 5% increments from 25-90%.
NoteIf the humidity level is outside the range, the display continues to show either 25% or 90%.
-
Select the Desired Fan Speed
Press the
button to set the speed to High or Low.
-
Set a Timer (if desired)
Press the
button to set the automatic shut off time.
- Press repeatedly to increase the shut off timer by 1 hr. increments up to 12 hrs.
-
Important Usage Info:
- The display shows the current humidity level.
- It takes 30 minutes of continuous operation to reach the desired humidity level the first time the product is used.
- If the product is restarted immediately after being shut down, there is a 3-minute delay to protect the compressor before the compressor begins operating.
- It is normal for the compressor to cause the product to vibrate while starting or stopping.
Need to contact us?
If you have other questions or concerns, reach out to our 24/7 Chat Support for further assistance.
