At a Glance
On some LG washing machine models, blinking LED light error codes help identify problems causing your washer to not function properly. Most errors codes on your LG washer can be resolved easily with a few troubleshooting steps. For alphanumeric error codes, please visit LG Washer Error Code List.
Try This
Filter the error codes by selecting the options that are blinking.
Select an errror code that resembles your display to see more information
DE Error Code
A dE error code means that the washer was not able to lock the drawer. This might be as a result of the drawer is not closed properly or the drawer is closed, but not locked.
-
1- Turn off the washer and pull the drawer open.
-
2- Check for items caught under the lid, including shipping material or clothing.
-
3- Close the drawer firmly.
-
4- Make sure that the lid is closed fully and press the Start/Pause button.
To fix this:
If the error code persists, the unit may require a repair service, reach out to our 24/7 Chat Support for further assistance.
DR Error Code
This is not an error, it is a special drain feature. DR indicates that the unit has timed out, and it is automatically draining the water in the unit.
This may happen in any of these two situations:
-
1- If the unit is paused during the cycle, and left idle for 8 minutes without resuming the cycle.
-
2- If the unit is powered on and left idle for 4 minutes without starting a cycle.
In both cases, DR will display to identify the action of the unit.
If the error code persists, the unit may require a repair service, reach out to our 24/7 Chat Support for further assistance.
EE Error Code
The EE error code on an LG washing machine indicates a problem with the main control board's EEPROM (Electrically Erasable Programmable Read Only Memory).
To fix this:
You can try unplugging the washing machine for 10 minutes. If that doesn't work, you may need to replace the main control board.
If the error code persists, the unit may require a repair service, reach out to our 24/7 Chat Support for further assistance.
E6 Error Code
The E6 error indicates an error about the clutch. This error can occur when a coin or a foreign object is stuck between the pulsator and the tub.
To fix this:
-
1- Remove every item in the wash tub.
-
2- Look inside the washer to check the bottom.
-
3- Check the seam between the drum and the pulsator to see if items such as a coin, zipper, or paper clip is stuck there.
-
4- If any item is found, remove it by using a pair of pliers.
If the error code persists, the unit may require a repair service, reach out to our 24/7 Chat Support for further assistance.
LE1 Error Code
An LE1 error code on an LG washer indicates a locked motor, often due to an obstruction or excessive load, and requires addressing the issue to allow the motor to spin freely.
To fix this:
-
1- Remove every item in the wash tub.
-
2- Look inside the washer to check the bottom.
-
3- Check the seam between the drum and the pulsator to see if items such as a coin, zipper, or paper clip is stuck there.
-
4- If any item is found, remove it by using a pair of pliers.
If the error code persists, the unit may require a repair service, reach out to our 24/7 Chat Support for further assistance.
PS Error Code
An PS error code on an LG washer indicates the supply voltage is not correct..
To fix this:
-
If unit wont power up, check the power source, the unit will need 120Vac (+/- 5%), and correct polarity.
If the error code persists, the unit may require a repair service, reach out to our 24/7 Chat Support for further assistance.
tE Error Code
A tE error is a temperature sensor error.
If the error code persists, the unit may require a repair service, reach out to our 24/7 Chat Support for further assistance.
PE Error Code
The PE error indicates that the water pressure sensor isn’t working properly.
To fix this:
-
It could be that the unit is oversudsing, either due to too much detergent or softner being used, running a tub clean with a cleanser, such as, Affresh could fix the issue. If this does not resolve the issue,k a technitian may need to inspect the unit.
If the error code persists, the unit may require a repair service, reach out to our 24/7 Chat Support for further assistance.
FE Error Code
The FE error indicates a fill error. The code displays when the water level gets too high. This may be caused by a faulty inlet valve, and the machine could be filled with water while it is turned off.
To fix this:
-
Turn off the water to the unit, perform a drain only or spin only cycle to drain out any excess water, then unplug the unit until repair service is completed.
If the error code persists, the unit may require a repair service, reach out to our 24/7 Chat Support for further assistance.
DL Error Code
A dL error indicates that the door latch switch is not functioning properly. There are possible causes that could lead to the display of this code, such as:
-
A- An item could be caught inside the door.
-
1- Remove items.
-
2- Unplug the unit for 10 seconds.
-
3- Plug unit back in, and try to start the cycle again.
-
B- The door switch is malfunctional.
-
C- The door latch itself has been damaged.
To fix this:
If the error code persists, the unit may require a repair service, reach out to our 24/7 Chat Support for further assistance.
